Manual installation of Bi-Pipe Audi S4

The installation procedure, Bi-Pipe audi s4:
1. allow the engine to cool before you begin Setup.
2. Open the throttle body cover by twisting machines two ¼ turn Mounting screws and pull straight up on the cover.
3. remove the two screws securing the rozprowadzaly fresh air inlet.
4. delete the rozprowadzaly by pulling on the ?rst on the left, and then pull out.
5. remove the two nuts and washers 8 mm sensor security pulse.
6. remove the two 5 mm allen head screws pulse sensor security bracket and remove the bracket.
7. Gently distract the clip at the top of the chassis plug and unplug the pulse sensor plug-ins.
8. loosen the front of the throttle body boot clamps.
9. back the throttle body to Generously

readmore..

1991-2006 Acura NSX exhaust system installation instructions

Thank you for purchasing system Comptech stainless steel exhaust gas at the Acura NSX (1991-2006). All of the components has been designed and manufactured using the latest technologies and materials. Please take a moment to read this page about the instruction how to manually and guarantee exactly before the commencement of any work. Always work in a clean and use proper safety equipment and tools to avoid any potential damage or injury. Comptech recommends genuine Acura service manuals in order to complete these instructions. All Comptech products are designed to be installed by the installer.

readmore..

1994-01 Acura Integra and 1997-01 Honda CRV Hyper intake inlet/Dragon

Additional parts are needed when you have a Dragon, 1 x Coupler ''-(6-benzoylamino-3-sulfonato-2-naphthylazo)-biphenyl-1, 3'œ, 3?-4?-(6-benzoylamino-3-sulfonato-2-naphthylazo)-biphenyl-1, 3'œ, 3?/2 x 4?-(6-benzoylamino-3-sulfonato-2-naphthylazo)-biphenyl-1, 3'œ, 3? Clamp bolts securing the box to remove the air cleaner, loosen the clamps on OEM intake pipe OEM rubber. Delete the transfer of coolant/PVC hardline from OEMs and from the inlet to the engine. Mark the beginnings of hose wire coolant, install hose, 10 mm, supplied in a set location, 2. Remove OEM rubber tube, remove the air cleaner box OEM by pulling up. Wipe clean of any lubricant throttlebody, install 2.5 "-Coupler ''-(6-benzoylamino-3-sulfonato-2-naphthylazo)-biphenyl-1, 3'œ, 3? at throttlebody, safe from the OEM clamp.

readmore..

2000-2001 Acura Integra instruction System of cold air type r

Read and understand the instructions before attempting to reinstall this product.
1) Introduction
whether a vehicle is branded) parked on a level surface.
(b)) and set the parking brake.
c) Disconnect the negative battery terminal.
d) if the engine has been started within the last two hours to cool down.

2) removal of stocks of the intake air

readmore..

2001-2003 Acura 3.2 CL cold air system installation instructions

Installation for the 2001-2003 Acura 3.2 CL cold air system:
1) Introduction
whether a vehicle is branded) parked on a level surface.
(b)) and set the parking brake.
c) Disconnect the negative battery terminal.
d) if the engine has been started within the last two hours to cool down.

2) removal of stocks of the intake air
delete a set of primary field) air and attach equipment on the inside of the fender well.
(b), disconnect the breather hose) and air hose, fuel-injection Control System air intake Duct.
(c)) and remove the cord pull in air inlet throttle body.
d) Jack on the front of the vehicle and support using the correctly rated stands of Jack.
and) delete lower front splashguard.
II), delete the Left front tire and remove inside splashguard (inner fender liner).
(e)) delete resonator from underneath the vehicle.

readmore..

2002-04 ACURA RSX-S race instructions header

Because it is a product of "Race", will meet the emission standards. How is a product of "Race", will also "check engine" light illuminating after three complete cycles. This is not a problem for obtaining the maximum performance. "Check engine" lamp does not cause the engine computer, go to the "safe mode". It is only an indicator function of the system. Special note for header stainless Racing Jackson: congratulations header stainless Racing Jackson. The trip of the header on the market today. Stainless steel is made of 100%. Including flanges. This will not be a Noncorrosive steels rust! But special care must be taken during installation and maintenance of stainless steel pipe, if you want to always look good.

When the oil or fat, or even finger communication at the

readmore..

2002-up ACURA RSX (including 6-spd type-S) Precision Sport moving instructions

The B and M Precision Sport Shifter was designed to work on most 2002 + Honda Integra/Acura RSX (including 6-spd type-S) and the 2001 + Honda Civic models equipped with a manual transmission. It is designed significantly reduce shift throw and improve the feel of moving. Verification of components and tools lists at the beginning of these instructions supplied parts and tools required to install a network of B and M Precision Sport Shifter. Installation B and M Precision Sport Shifter can be obtained by anyone with minimal mechanical experience.

B and M Precision Sport Shifter can be installed in less than an hour carefully follow the instructions. Read all instructions first familiarize yourself with the parts, tools and procedures. This set contains all the items necessary for installation.

readmore..

2003 Acura 3.2 TL vehicle information

TL 2003 3.2 is a 4-door, 5-passenger luxury sedan or sports Sedan, available in 4 TRIM, ranging from Sedan
to the Type-S from the Navigation System. The closest competitors of TL 3.2 shall include the Audi A4 2003, the town of Lincoln Automobile and Volvo S80. After the introduction of the Sedan comes in the form of standard 3.2-liter V6, 225-horsepower

readmore..

K20A billet throttle cable bracket tube, instructions

This bracket is the solution for installing a K20A cable (R ITR, CTR, Euro-) activated throttle body K-Powered EG, EK, DC2 or EF when:
-Allowing short throttle cable OEM (Acura 17910-ST7-L01) swap
-Eliminate the interference of the throttle cable/bracket (from fuel tubes, hoses, Hoods, etc.)
-Made of aluminium 6061 T6 billet, tube, machined to high quality.

MODIFYING CABLE THROTTLE RESPONSE OF GSR
1. Obtain cable throttle Acura Reaction GSR 94-01 (Acura P/n: 17910-ST7-L01).
2. slide the metal retaining ring off the throttle cable boot.
3. the use of wire-cutting pliers to cut a slit foundations Ring, for removal of the throttle cable. Careful not to damage the throttle cable wires, while cutting.
4. using scissors to trim the throttle cable computer startup as shown. To cut a second bellow, leaving the three remaining on the bellows. Again, be sure not to allow a wire cable scissors mar steel braided throttle.

readmore..

Interior ventilation filter installation

The Interior ventilation filter, Acura RDX, TL, TSX, Honda Accord, Civic, CR-V. Ventilation filter inside the filter housing is located in the glove compartment door.
1. open the glove box door. Grasp and push down on the door of gloves with rod on the right side door glove box.
2. Insert the screws flat tip the driver door glove box stays and gently apply pressure inside the Chamber to remove the glove box door stays. Bottom of the door swing glove box.
3. (some models 2004) push push-pins Center hole (2) is located on the left and right-hand sides of the glove compartment lid and eject unlock them. After the contacts are, slowly remove the CAP Chamber glove box to the right. Are close to (10) the pins clamp which will come from a sequence. Unplug the electrical connectors (2)

readmore..

L SOHC Engines updated Timing belt tensioner 2002-2003 Acura 3.2

The revised timing belt tensioner, 2002-2003 Acura 3.2 l engines is part of the improvement of the product by Acura. The original belt tensioner design time is filled with oil vibrations in the euro area. In view of the situation of production of oil can leak the tensioner. In the case of the loss of enough oil timing belt loosens and causes the engine noise. Worst case scenario lose the belt tension and enable losing camshaft timing. Vehicles with improved tensioner should be identified by a mark punched above sixth digit VIN code of the engine compartment, as shown.
Cylinder head gasket leaks on 1988-95 Honda Civic 1.6

readmore..